Vehicle Applications

Jeep, Chrysler, & Dodge | SUV, Sedan, & Coupe

• (2007-2025) | Amplified & Non-Amplified Systems

↳ Installation Time

Introduction

These instructions will guide you through the sub kit installation for your vehicle.

TIP Before you begin, review these instructions thoroughly and ensure that all parts are present and tools are available.

WARNING Metra Electronics does not assume any responsibility for damage resulting from incorrect Installation.

↳Tools

• Phillips Driver
• Rachet
• Sockets: 7mm, 8mm, 10mm
• Torx Bit: T40
• Panel Removal Tool
• Unibit (Step Drill Bit)
• Wire Strippers
• Soldering Equipment
• Rivet Nut Setter (Optional)
• Zipties

↳ System Components

• Axxess AXSUB Interface
• Vehicle Specific T-Harness (LD-DSP-CH4, LD-DSP-CH5, LD-DSP-CH8)
• Active Noise Canceling (ANC) Harness (ANC_CHH1 & ANC-CHH2)
• Raptor R5 Pro Series 4AWG Amp Kit
• 12GA Speaker Wire (LD-12GA-6)
• Vibe Powerbox 650.1 Mini Amplifier

Safety Protocols & Preliminary Vehicle Preparation

Battery Disconnection & SRS Integrity

The strategic preparation of a vehicle is not merely a preliminary step; it is the foundation upon which high-fidelity electrical integration is built. In modern automotive systems, where sensitive electronics and safety modules are interconnected, following a disciplined preparation protocol ensures both the longevity of the aftermarket hardware and the integrity of the vehicle’s factory systems. Electrical safety is the non-negotiable prerequisite for a successful installation.

WARNING ELECTRICAL & SRS SAFETY With the key removed from the ignition, use a 10mm socket to disconnect the negative battery terminal. It is critical that all airbag indicator lights remain plugged in during installation. Do not reconnect the battery if any SRS (Supplemental Restraint System) components are disconnected, as this will trigger permanent fault codes and system errors.

Adhering to these safety steps prevents accidental electrical shorts and safeguards the SRS system, providing a secure environment for subsequent technical integration.

Interface Compatibility

↳ LD-DSP-CH4

System Type: Amplified & Non-Amplified

↳ LD-DSP-CH5

System Type: Amplified & Non-Amplified

↳ LD-DSP-CH8

System Type: Amplified & Non-Amplified

Active Noise Cancellation (ANC) Diagnostics

Active Noise Cancellation (ANC) is designed to improve cabin acoustics by emitting counter-frequencies through factory speakers to mask engine noise. However, this system views the high-output, low-frequency output of an aftermarket subwoofer as "noise" and will attempt to cancel it, creating a significant conflict.

• ANC-CHH1 is for Non-Amplified with ANC Module.
• ANC-CHH2 is for Premium Audio RFU, Premium Plus Audio RFA/RFL

↳ ANC-CHH1

System Type: Non-Amplified

↳ ANC-CHH2

System Type: Amplified

CAUTION ANC INTERFERENCE Failure to bypass an active ANC system results in a distinct low-frequency drone or "hum" that increases in intensity with engine RPM, even when the radio is off. Identifying the ANC status during the diagnostic phase prevents invasive rework after the cabin has been reassembled.

Axxess AXSUB Interface Integration

The Axxess AXSUB interface serves as the system's primary signal processor. It intercepts the factory radio's output and converts it into a clean, high-voltage 5V RMS signal. This provides the aftermarket Vibe amplifier with a low-noise input, ensuring the bass remains articulate and powerful.

1. Disassembly: For vehicle-specific disassembly instructions, refer to metraonline.com. Enter the vehicle's year, make, and model into the Vehicle Fit Guide for Radio Install Kits.

2. T-Harness Connection: Seat the vehicle-specific T-Harness between the radio and the factory wiring. (FIG A, above)
3. 8-Pin Molex Requirement: The harness features an 8-pin Molex male-to-female connector. These must be connected to each other to maintain the factory speaker circuit. Failure to do so will result in a total loss of sound from factory speakers. (FIG B, above)
4. Remote Turn-On Wire: Connect the Brown Remote Turn-On wire from the interface to the Blue Remote Wire from the amp kit. wire. (FIG C, above)
5. Signal Routing: Route the RCAs and the extended remote wire along the passenger side floorboard. At this time, Metra recommends running the PB650.1D bass knob wire (FIG D) from the preferred mounting location in the dash, along with the RCA’s and remote turn-on wire, to the amplifier location.

6. Door Trim Removal: Remove the trim panels from the passenger-side front and rear doors to properly route the wire bundle to the rear passenger area.
7. With the dashboard electronics integrated, the focus transitions to routing the signal and remote cables through the chassis, following the factory wire looms to ensure a clean, protected path to the rear of the vehicle.

Power Wire Installation

A high-performance amplifier requires stable power. Using 4 AWG Oxygen-Free Copper (OFC) ensures the system remains stable under heavy transient loads without voltage drops that could trigger protection modes.

Power Wire Routing

Access the OE battery, usually located in the engine compartment.

1. Connect the 18-inch 4 AWG power cable to the MANL fuse holder.
2. Use a socket to attach the 18” 4 AWG power cable to an available battery lug.
3. Connect the 17 ft 4 AWG power cable to the opposite end of the MANL fuse holder.
4. CRITICAL SAFETY WARNING: Do not insert the 100-amp MANL fuse into the holder until the entire installation is complete and all wiring has been double-checked for shorts.

Chassis-to-Cabin Routing

1. Path: Route the 4GA power wire down the firewall and along the frame rail. Secure the wire with zip ties away from heat sources or moving suspension parts.
2. Entry: Route the power wire into the vehicle cab through an unused grommet in the firewall. Secure the cable with zip ties, keeping it away from high-heat sources like the exhaust. Remove the grommet, cut a small access point for the wire, and reinstall.
3. Use a Unibit if a new hole is required, ensuring the edge is protected.

Grounding Best Practices

• Length: Keep the 4 AWG ground cable to a maximum of 3 feet.
• Contact: Find a solid metal point on the chassis near the amplifier. Sand the area to bare steel for maximum surface conductivity.
• Prohibition: It is not recommended to use a seatbelt anchor point, as they are often treated or insulated, creating high-resistance points.

This secure power foundation ensures the Vibe Powerbox 650.1 operates within its designed thermal and electrical limits, preventing premature equipment failure.

Amplifier Calibration & Thermal Management

"Gain" is a process of input sensitivity matching rather than a volume control. Setting the gain incorrectly is the primary cause of hardware failure in high-performance systems.

Baseline Settings Matrix: Vibe Powerbox 650.1

Do not increase the Gain dial beyond the 12 o'clock position. Exceeding this limit will cause the subwoofer to exceed its thermal capacity, resulting in permanent hardware failure.

System Programming

The AXSUB interface requires a signal-sensing handshake with the factory radio to synchronize data and turn-on protocols.

Programming Checklist

1. Insert the 100-amp MANL fuse and reconnect the negative battery terminal.
2. Turn the ignition ON. Set the radio audio volume all the way down and the Vibe remote bass knob to 1/4 volume.
3. Gradually increase the radio to a normal listening level.
4. Wait 15 seconds for the interface to sense the audio signal and auto-program.
5. Verify that muting the radio or turning the volume to zero deactivates the amplifier.

Before permanently reassembling the vehicle trim and dashboard, perform a final inspection of all wire routing to ensure no cables are pinched or exposed to moving parts.

Subwoofer Options

The Vibe 650.1 is capable of handling up to a 1 Ohm load. If you are using an existing enclosure, consult the manufacturer's recommended wiring setup. If you are looking to add an enclosure, see the best paired options mentioned below.

↳ BAMIT12-V4

• 2007 - 2018 JEEP JK
• 2018 - 2026 JEEP WRANGLER
• 2021 - 2026 FORD BRONCO (2D/4D)

Unveiling the Vibe BAMIT12-V4 Compact Enclosure with Jeep Integration! - Vibe

For car audio enthusiasts, the quest for powerful, impactful bass often comes with a significant compromise: boot space. Traditional subwoofer enclosures can be bulky, eating into valuable cargo room and making them impractical for many vehicles, especially those designed for adventure. But what if you could have the best of both worlds? Prepare to meet […]

vibeaudio.co.uk

↳ JP-GL1-12

• OEM-Fit Sub Enclosure
• Jeep Gladiator JT 2020-2025

Metra Electronics | Products

This custom-fit, single 12-inch ported subwoofer enclosure is designed to mount cleanly under the rear cab seat in the 2020-2025 Jeep® Gladiator JT*. Developed by Metra’s Master Technicians, this up-firing enclosure delivers a precise OEM-style fit while maximizing performance and space efficiency. If you want powerful, hard-hitting bass in your Jeep®, this vented 12-inch enclosure is an ideal solution.

www.metraonline.com

↳ SLICKMIT12-V3

• 12” 1500 Watts Passive Bass Enclosure
• SUV / SEDAN / COUPE

SLICKMIT12-V3 Slick 12 Inch 1500 Watts Passive Bass Enclosure - Vibe

BEST FITMENT – The Multi Installation technology allows for perfect fitment in many applications. With “Power”, “Stealth” and “Space saving” fitment options all from one enclosure.

vibeaudio.co.uk

Troubleshooting

This concludes the installation. Ensure all interior panels, trim pieces, and safety components are restored to their factory positions. Your JP-SUB-KT1 system is now fully integrated and ready for service.

Technical Support

TIP If you encounter any difficulties during installation, please carefully review the instructions and ensure that the installation was performed exactly as instructed.

Our dedicated team is here to provide you with expert assistance and guidance. Whether you're troubleshooting an installation, seeking product information, or looking for technical advice, we're committed to ensuring your experience with Metra Electronics products is seamless and satisfying.

WARNING Before contacting Metra Technical Support, ensure the vehicle is in a ready state to perform troubleshooting steps.

Contact

Email

Submit a Support Ticket

(386) 257-1187

Vehicle Fit Guide

Hours (EST)

Monday-Friday: 9:00 am - 7:00 pm Saturday: 10:00 am - 5:00 pm Sunday: 10:00 am - 4:00 pm

On This Page

• Vehicle Applications
• Jeep, Chrysler, & Dodge | SUV, Sedan, & Coupe
• ↳ Installation Time
• Introduction
• ↳Tools
• ↳ System Components
• Safety Protocols & Preliminary Vehicle Preparation
• Battery Disconnection & SRS Integrity
• Interface Compatibility
• ↳ LD-DSP-CH4
• ↳ LD-DSP-CH5
• ↳ LD-DSP-CH8
• Active Noise Cancellation (ANC) Diagnostics
• ↳ ANC-CHH1
• ↳ ANC-CHH2
• Axxess AXSUB Interface Integration
• Power Wire Installation
• Power Wire Routing
• Chassis-to-Cabin Routing
• Grounding Best Practices
• Amplifier Calibration & Thermal Management
• System Programming
• Programming Checklist
• Subwoofer Options
• ↳ BAMIT12-V4
• ↳ JP-GL1-12
• ↳ SLICKMIT12-V3
• Troubleshooting
• Technical Support
• Contact
• Hours (EST)