→ Programming Synced Blocks
→→ Tap Method Synced Block
Programming the AXSWC-2
In order to effectively program the AXSWC-2, the aftermarket radio needs to be (or remain) completely wired. The AXSWC-2 harness should be wired and the (Steering Wheel Control) SWC 3.5mm Jack or SWC wiring should be connected.
NOTE
If your aftermarket radio is from the Sony XAV Series, before programming to the vehicle, you must:
1. Turn the radio On.
2. From the radio's home screen, click Settings.
3. Click System.
4. In the Steering Wheel Settings section, toggle the Custom switch to Off.
5. Return to the Main Menu.
6. Power Off the radio.
You may now proceed with programming the radio to your vehicle with the steps below.
Follow the steps below to programming the AXSWC-2 to your vehicle:
- Open the driver’s door. Keep it open during the programming process.
- Turn the vehicle’s ignition On.
- Plug in the AXSWC-2.
- The LED on the SWC begins rapid flashing Green and Red.
- (Optional) If the LED does not turn on, refer to Connections above and ensure all steps were performed precisely.
- Tap the Volume Up button on the steering wheel at a steady heartbeat pace (1, rest, 2, rest, 3, rest, etc.) until the rapid flash stops (3-5 seconds).
- (Optional) If the Green and Red flashes are missed, reset the AXSWC-2 (as explained below) and restart the programming process from the beginning.
- Stop tapping the Volume Up button. The AXSWC-2 is being programmed into the vehicle’s steering wheel controls (SWC).
- The Red and Green LED flashes represent a different radio manufacturer for the SWC interface to detect.
- Upon successfully programming, the LED turns solid Red.
- Test all functions of the AXSWC-2 installation for proper operation.
→→ Auto Method Synced Block
Programming the AXSWC/AXSWC-2
In order to effectively program the AXSWC-2, the aftermarket radio needs to be (or remain) completely wired. The AXSWC-2 harness should be wired and the (Steering Wheel Control) SWC 3.5mm Jack or SWC wiring should be connected.
NOTE
If your aftermarket radio is from the Sony XAV Series, before programming to the vehicle, you must:
1. Turn the radio On.
2. From the radio's home screen, click Settings.
3. Click System.
4. In the Steering Wheel Settings section, toggle the Custom switch to Off.
5. Return to the Main Menu.
6. Power Off the radio.
You may now proceed with programming the radio to your vehicle with the steps below.
Follow the steps below to programming the AXSWC-2 to your vehicle:
- Open the driver’s door. Keep it open during the programming process.
- Turn the vehicle’s ignition On.
- Plug in the AXSWC-2.
- The LED on the SWC begins rapid flashing Green and Red.
- (Optional) If the LED does not turn on, refer to Connections above and ensure all steps were performed precisely.
- The AXSWC-2 will enter auto-detect mode. No action is required until the LED begins flashing Green and Red.
- (Optional) If the Green and Red flashes are missed, reset the AXSWC-2 (as explained below) and restart the programming process from the beginning.
- The AXSWC-2 is being programmed into the vehicle’s steering wheel controls (SWC).
- The Red and Green LED flashes represent a different radio manufacturer for the SWC interface to detect.
- Upon successfully programming, the LED turns solid Red.
- Test all functions of the AXSWC-2 installation for proper operation.
→→ Hold Method Synced Block
Programming the AXSWC-2
In order to effectively program the AXSWC-2, the aftermarket radio needs to be (or remain) completely wired. The AXSWC-2 harness should be wired and the (Steering Wheel Control) SWC 3.5mm Jack or SWC wiring should be connected.
NOTE
If your aftermarket radio is from the Sony XAV Series, before programming to the vehicle, you must:
1. Turn the radio On.
2. From the radio's home screen, click Settings.
3. Click System.
4. In the Steering Wheel Settings section, toggle the Custom switch to Off.
5. Return to the Main Menu.
6. Power Off the radio.
You may now proceed with programming the radio to your vehicle with the steps below.
Follow the steps below to programming the AXSWC-2 to your vehicle:
- Open the driver’s door. Keep it open during the programming process.
- Turn the vehicle’s ignition On.
- Plug in the AXSWC-2.
- The LED on the SWC begins rapid flashing Green and Red.
- (Optional) If the LED does not turn on, refer to Connections above and ensure all steps were performed precisely.
- Hold the Volume Up button on the steering wheel.
- (Optional) If the Green and Red flashes are missed, reset the AXSWC-2 (as explained below) and restart the programming process from the beginning.
- Stop holding the Volume Up button. The AXSWC-2 is being programmed into the vehicle’s steering wheel controls (SWC).
- The Red and Green LED flashes represent a different radio manufacturer for the SWC interface to detect.
- Upon successfully programming, the LED turns solid Red.
- Test all functions of the AXSWC-2 installation for proper operation.
→ Additional Settings/Details/Troubleshooting Synced Block
Resetting the AXSWC-2
Radios with Built-In SWC Menus
LED Feedback
Changing Radio Type
Button Remapping
Dual Assignment Instructions
Troubleshooting
- Verify that 12-volt power and chassis ground have a solid connection.
- Verify your connections are correct and that the view of the connector was established properly when locating your connections.
- Verify the 3.5mm jack is secured in its proper location and not a secondary one.
- Remove any aftermarket T-taps or barrel connections. These will add resistance to a resistance-based system.
- If using a 2-wire or 3-wire universal-style radio, verify proper connection to the radio using the female 3.5 jack.
- (Pioneer radio users) If the radio buttons are not functioning as expected or at all, attempt the following:
- Insert and remove the 3.5mm male jack in and out of the back of the radio five to six (5-6) times.
- On the final insertion, ensure the jack is well set.
- Reset and reprogram the AXSWC-2.
- If you’ve established all connections and the AXSWC-2 won’t connect, remove any aftermarket connectors, T-taps, barrel connectors, and quick connectors. These will all add resistance.
→ Radio Troubleshooting
If you experience issues programming your Radio, the guides below can help you troubleshoot:
Manual Programming
On The Table
- → Programming Synced Blocks
- →→ Tap Method Synced Block
- Programming the AXSWC-2
- →→ Auto Method Synced Block
- Programming the AXSWC/AXSWC-2
- →→ Hold Method Synced Block
- Programming the AXSWC-2
- → Additional Settings/Details/Troubleshooting Synced Block
- Resetting the AXSWC-2
- Radios with Built-In SWC Menus
- LED Feedback
- Changing Radio Type
- Button Remapping
- Dual Assignment Instructions
- Troubleshooting
- → Radio Troubleshooting
- Manual Programming